Sony RM-V18A Manual de usuario descargar pdf

SONY

3-864-372-12(1)

RM-VI8 A

Remote Commander

Operating Instructions

Manual de instrucciones (parte posterior)

English

For the customers in the U.S.A.

WARNING

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is coimected.

• Consult the dealer or an experienced radio/TV technician for help.

You are cautioned that any changes or modifications not expressly

approved in this manual could void your authority to operate this

equipment.

Setting Up the Remote Commander

Before you can start using the Commander, you must first set it up.

This manual describes everything you need to know to set up the

Commander, including:

• Installing the batteries.

• Presetting the Commander with the codes for your TV, VCR, Cable

box and other audio components.

About Presetting the Commander

The Commander is preset at the factory to operate Sony brand

components.

If you're using the Commander with a Sony component, you won't

need to preset the Commander before you start using if.

To set up the Commander to use with other (non-Sony)

manufacturers' components, or to use with a component that is not

preset at the factory, you'll need to follow the instructions in this

manual to preset the Commander with the correct code number for

your components. (See the supplied "Component Code Numbers"

also.)

Component that can be preset

Button

Factory setting

'TV

Sony TV

VCR VCR

Sony VHS VCR

Cable box/Receiver/CD player/ CABLE

—

Tape deck/TV/VCR

AVI

Sony Receiver

AV2 Sony CD player

Notes

• The Commander can be set up to tqjerate only one component per

button - unless their code numbers happen to be the same. For

example, you carmot set up the Commander to operate a Sony TV

and a Panasonic TV simultaneously (because they use different

code numbers).

• You may not be able to operate even a Sony brand component with

the factory presetting. In such a case, follow the procedure in

"Setting the Code."

Installing the Batteries

Slide open the batter)' compartment and insert tw'o size AA (R6)

batteries (not supplied).

Be sure to line up the + and - on the batteries with the + and - on the

battery compartment.

When to replace the batteries

Under normal conditions, batteries will last up to six months. If the

Commander does not operate properly, the batteries might be worn

out Replace the batteries with new ones.

Notes

• Replace both batteries with new ones.

• Do not take more than 20 minutes to replace the batteries;

otherwise, your setting of the code numbers will be ereised.

Notes on Batteries

• Do not mix old batteries with new ones or mix different types of

batteries together.

• If the electrolyte inside the battery should leak, wipe the

contaminated area of the battery compartment with a cloth and

replace the old batteries with new ones. To prevent the electrolyte

from leaking, remove the batteries when you plan not to use the

Commander for a long period of time.

Setting the Code

Follow the steps 1 and 2 below for each component you plan to use

with the Commander.

Step 1: Entering the Code Number

1 See the supplied "Component Code numbers", «md find the code

number in double figures for the desired component.

If more than one code number is listed, use the number that's

listed first to complete the steps below.

For example, if you're setting up a Philips' VCR, you would use

the code number 13.

If your component isn't listed, see "Searching for the Correct

Code."

2 Press and release the S (set) button.

3 Press the button of the component that

you want to set up.

Note

On the AVI, AV2, and CABLE buttons,

"receiver", "CD player", <md "cable box"

are tissigned respectively at the factory. But

you can also assign other components on

these buttons. For details, see "Changing

the Component Type on the AVI, AV7, and

CABLE buttons."

VCR CABLE

AVI

AV2

1 2 3 4 5 6 ... 11 12

Indice de contenidos

Pagina 1 - RM-VI8 A

Pagina 2 - < и >

TV/VCR/COMBOBrandComponentCode No.ScmyVCR01 (VTRl; Beta)02 (VTR2: 8 mm)03 (VTR3: VHS)04 (VTR4: DV)05 (VTR5: DV)06 (VTR6: DV)TV01AdmiralVCR 30TV02,14,0

Pagina 3 - Volume Control

CBLCDBrandCode No.BrandCode No.Hamlin/Regal22, 23, 24,25, 26 Sony01Jerrold/G.I.01,02,03,04,05,06, 07, 08,18Aiwa30, 32Oak27,28, 29Denon24Panasonic19,20

Pagina 4 - Specifications

MD/DAT (RM-V40AA^701A/801)BrandCode No.Sony01, m (DAT)Denon02Kenwood03Teac 04Panasonic 05Marantz 06JVC07Sansui 08Pioneer10 (DAT)Onkyo 10 (DAT)Mini Hi-

Pagina 5 - Programación del código

l-titcr the comp^>nont's axle numbor. Гог ovamplo. it you're entering the axle tor a Philips VCK. you would press and re

Pagina 6 - Búsqueda del código correcto

Changing the Factory Setting for the Volume Control1 Prt'ss and release the S (set) button. s")2 Press the AVI button. AVIRemote Button

Pagina 7 - Control de un componente

Operating a Cable boxOperating a tape deckQ]To sc't up tlio Commander.ID To switch to Cable box operation. Press the button on which the Cable bo

Pagina 8 - Para los clientes de EE.UU

EspañolPara los clientes de EE. UU. ADVERTENCIAEste equipo ha sido probado y se ha encontrado que cumple con los límites para dispositivos digitales d

Pagina 9 - OD I Code No. I ^

Paso 2: Comprobación del funcionamiento de un número de código1 Conocto la allmoJ'vtación del componente quo desco ajustar.2 Apunto con ol tolo

Pagina 10 - & 35

Cambio del ajuste de fábrica para el control de volumen1 Presiono y suelte el botón S (ajuste). (i ^2 Presione el botón AVI. AVI3 Presione la tecl

Pagina 11 - DBS (RM-V40AA/701A/801)

Control de un adaptador para cablevisiónControl de un deck de cassettesJ'nisr.mi.ir ol tclomanJo.Para cambiar a la operación del adaptador para c

Pagina 12 - Codes de minichaine hifi

Comentarios a estos manuales

Sin comentarios

Sony RM-V18A Manual de usuario

Busca en linea o descarga Manual de usuario para Panel De Control Sony RM-V18A. Sony RM-V18A User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Panel De Control Sony RM-V18A