Sony RM-V8 Manual de usuario descargar pdf

3-856-605-11 (1)

Remote Commander

Operating Instructions

Manual de instrucciones (parte posterior)

RM-V8

English

WARNING

This equipment has been tested and found to

comply with the limits for a Class B digital device,

pursuant to Fart 15 of the FCC Rules. These limits

are designed to provide reasonable protection

against harmful interference in a residential

installation. This equipment generates, uses, and

can radiate radio frequency energy and, if not

installed and used in accordance with the

instructions, may cause harmful interference to

radio communications. However, there is no

guarantee that interference will not occur in a

particular installation. If this equipment does

cause harmful interference to radio or television

reception, which can be determined by turning the

equipment off and on, the user is encouraged to try

to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment

and receiver.

• Connect the equipment into an outlet on a circuit

different from that to which the receiver is

connected.

• Consult the dealer or an experienced radio/TV

technician for help.

You are cautioned that any changes or

modifications not expressly approved in this

manual could void your authority to operate this

equipment.

About This Remote

Commander

This Remote Commander can operate any of the

following video components. If you're using this

Commander with a Sony brand TV and a Sony

brand VHS VCR, you won't need to preset the

Commander before you start using it. However,

you will need to set up the Commander if it cannot

operate even a Sony brand component and you

have a cable box. Each component is assigned a

different button on the Commander:

Notes on Batteries

• Under normal conditions, batteries will last up to

six months. If the Remote Commander does not

operate properly, the batteries might be worn out.

When replacing batteries, replace both of them

with new ones.

• Do not mix old batteries with new ones or mix

different types of batteries together.

• Whenever you remove the batteries - to replace

them, for example - the code numbers you've set

are automatically erased and must be reset.

• If the electrolyte inside the battery should leak,

wipe the contaminated area of the battery

compartment with a cloth and replace the old

batteries with new ones. To prevent the

electrolyte from leaking, remove the batteries

when you plan to not use the Commander for a

long period of time.

Setting Up the

Commander

1 2 3 4 5 6 7 8

Indice de contenidos

Pagina 1 - Remote Commander

Pagina 2 - Batteries

CommanderThis Remote Commander can operate any of the following video components. If you're using this Commander with a Sony brand TV and a Sony

Pagina 3 - ( II II )

If you press a wrong button in step 4Press and release the S (Set) button and then go back to step 2.Step 2: Checking if the Code Number Works1 Power

Pagina 4 - ( II T )

Searcning тог the Correct CodeIf you've tried all the code numbers listed for your component and you still cannot get the Commander to work, try

Pagina 5 - Descriptions

Remote Button DescriptionsRemoteButtonOperates FunctionTVChanges the input mode( Tv/vioeo )VCRSwitches the signals supplied to the TV (from the antenn

Pagina 6

VCRPauseITVVCRCable boxChannel up: + Channel down: -©laTVVolume up: + Volume down: -TV Mutes volume on TV(muting)Press again to turn muting off.TVCabl

Pagina 7 - Troubleshooting

BrandComponentCode No.Mitsubishi/MGAVCR23, 24,25,26TV24,03,12Multitech VCR25, 38, 21NECVCR14, 36, 37TV 03,12OlympicVCR 09, 08Panasonic VCR08, 09, 06,

Pagina 8 - Specifications

TV14,13,15ShintomVCR15Signature 2000 (M. Wards)VCR38,27TV14,09SylvaniaVCR10, 08, 09, 38TV11,12, 03SymphonicVCR38TV23,39TV/VCRCombo23 (TV) & 38 (V