Sony RM-V10A Manual de usuario

RM-V10ASERVICE MANUALUS'ModelThe following parts are an available for service parts of this model.PARTS LISTPart No. Description 4-968-504-01 LID

Remote Button DescriptionsNot«;Buttons that are highlighted in the following table operate independent of the position of the slide switch.1 Rrmntt&ap

Opt'r iti’s f'wni t '0nTVVCRCaUei)MOiMnaliifK.f'Channeidown:-TV Volume up: tf Volume dcnwi:-TV Mutes volume on TV Press again to t

Component Code NumbersTVandVCRCodMSony VCR«(vmvHS)ttfVTKfcamm)caivnti:BciMi4IVOTOUgvot13,02TV19.30Diwwdvot39110.07TV31.32, IBTWCRCombo32 (IV) 39(VCnEf

CcBapoiMmC^Nwnb»t»(oOBrtnn«d) CsbtoBOXCodMRCAffROSCANvat 04.0S.0(«7,oaiosiiaiTTVQZ,(8,0<IS. os. 07.01$«mingvat zan.t»IV 23,11.12.03TV/VOtCombolomSr

TroubleshootingIf you^ having proMMiu Mtting up or iMtog tiM Ramota Commindan When setting iq> the Cbomiandcr, eaiefaUy gd throu^ theprooeduzes de

f«ISONMMIMU AM MOOUCftUMITED WARRANTY \♦«>A CNv E tilt Mllii ЙММИ! АррИЯ on Aé pItAfd TMP WIHMPlf iPMlP P^WPw Рриер pf 1 vPW Pi UMS pw^wpp SOW M

« «bMk iMmKr oii^ «InM «*• *• *ndiA wSwv Sm*e Oww* Iw»« wewi« *» IWiKAi «f •« Mowino Iwm nwl k* MkiM «tan «•MHMCf cmrai*• ynduei fNpM w m «t taka »Mt

WARNINGThis equipnnait has been tested and fbimd to comply witii the limits for a Class B digital device, pursuant to Part 15 of die PCC Rules. These

Contents►♦♦•MM»»**»—**»*»»—»»»»*****—*>♦**♦♦♦*♦**»•**—*•*—»*»•♦•»*'S«t№ig up tti* RMnoto CommandMrInstiling the Batteries Setting the Code .

Setting Up the Remote CommanderBefote you can start using the Remote Commander, you must first set it up. This booklet describes everything you need t

Installing the Batteries Slide open the battery craxipartment and insert two size AAbatteries (not supplied).Be sure to line up tfve and - on the bat

CABLESetting the CodeStep 1: Entering th« Code Number1 Power off component you want to set up. Then set the slide switdi on the iwmote Com

step 2: Checking if the Code Number Works1 Aim tfte Remote Commander at die c(»nponent and press die POWER button.The component should power on.2 Wh

Searching for the Conrect CodeIf you've tried all the code numbers listed for your componentaiid you stQl cannot get №e Commander to work (or if

VCRUsing the Remote CommanderTurning On/Off a Component1 Set the slide swifcdi on the RemoteCommander to VCR (to turn on/otf a VCR), CABLE (to turn o