Sony PCV-RX460 Manual de usuario

x

VAIO® System Reference Manual86System I/O Address Map Address Range (hex)Description0000h-000Fh Direct memory access controller0010h-001Fh Motherboar

Miscellaneous Technical Information8703C0h-03DFh SiS 730S03F0h-03F1h Motherboard resources03F2h-03F5h Standard Floppy Disk Controller03F6h-03F6h SiS 5

VAIO® System Reference Manual88Memory Map Address range Default configuration00000000h-0009FFFFh System board extension for ACPI BIOS000A0000h-000AFF

Miscellaneous Technical Information89IRQ Settings IRQ Settings00 System timer01 Standard 101/102-Key or Microsoft Natural Keyboard02 Programmable int

VAIO® System Reference Manual90

91Chapter 8SpecificationsThis chapter describes the technical specifications for the SonyPCV-RX450/PCV-RX460 computer.Processor Chipset PCI Bus AGP

VAIO® System Reference Manual92DIMM Configurations Memory Modules (DIMMs) L2 Cache Graphics DIMM1** The PCV-RX450/PCV-RX460 is shipped with 128 MB.

Specifications93Audio Communications I/O and Expansion Slots Sound chip SiS 730S Audio ControllerWave synthesis 64 voice polyphony wave table synthes

VAIO® System Reference Manual94Floppy Disk Drive and Controller Hard Drives and Controllers Drive DescriptionFloppy disk controller 82077-compatible (

Specifications95Optical Drives Drive DescriptionDVD-ROM driveDVD-ROM read*CD-R/CD-ROM read†CD-RW read‡* Data on a DVD-ROM is read at a variable transf

xiContentsNotice to Users ... iiOwner’s Record...

VAIO® System Reference Manual96System BIOS Make and model Award-basedROM 2 MB flash-ROMPasswords User and supervisor passwords supportedPower managem

97IndexAadd-in cardinstalling 26removing 27address map, system 86AGP slot connector 52audio specifications 93Bbattery - See lithium batterybeep codes

VAIO® System Reference Manual98drivesIDE connectors 53installing additional 3.5-inchdrive 41DVD-ROM driveperformance of discs 3, 95Eerror messagesbeep

Index99microprocessor - See processormodel numbers iimodem - See communicationsmodem cardconnectors 70, 71view of 70, 71monitor - See displayMONITOR c

VAIO® System Reference Manual100TTELEPHONE connector 13Telephone Consumer Protection Act of1991 viTV interference vUUSB connectors 7, 11, 55user passw

VAIO® System Reference ManualxiiChapter 3 — Removing, Installing, and Replacing Components...

xiiiChapter 5 — Fax/Modem Card...69HomePNA Modem...

VAIO® System Reference ManualxivFloppy Disk Drive and Controller ...94Hard Drives and Controllers

1Chapter 1Identifying ComponentsThe following sections identify and describe each component that isvisible from the exterior of the VAIO® computer. In

VAIO® System Reference Manual2Front View

Identifying Components3Drives Drive DescriptionFloppy disk drive 3.5-inch, 1.44 MB.DVD-ROM driveDVD-ROM read*CD-R/CD-ROM read†CD-RW read‡* Data on a

VAIO® System Reference Manual4** Data on a CD-RW is read at a variable transfer rate, ranging from 8X at the innermost track to 20X at the outermost t

Identifying Components5Buttons and Switches Button or switch DescriptionPower/Stand by switch Turns system power on, off, or into Stand bymode.Floppy

iiNotice to Users © 2001 Sony Electronics Inc. Reproduction inwhole or in part without written permissionis prohibited. All rights reserved. Thismanua

VAIO® System Reference Manual6Indicators Indicator DescriptionPower/Stand by indicator Stand by (red) indicates the computer is inStand by mode.On (bl

Identifying Components7Connectors Connector Descriptioni.LINK® (IEEE1394)** To connect to a 6-pin i.LINK device, use the i.LINK connector on the back

VAIO® System Reference Manual8Rear View MouseKeyboardUSB1EthernetMonitorPrinteri.LINK (IEEE1394)SerialHeadphonesLine InMicLineTelephonePower

Identifying Components9Icons Icon DescriptionMouse portKeyboard portUSB portEthernet portPrinter/Parallel portMonitor porti.LINK® (IEEE1394) portSer

VAIO® System Reference Manual10Line In jack (audio)Mic (microphone) jackLine jack (for telephone line from service jack)Telephone (for telephone)Icon

Identifying Components11I/O ConnectorsThe following section identifies the various I/O connectors.Keyboard and Mouse PortsThe keyboard and mouse ports

VAIO® System Reference Manual12Printer/Parallel PortThe printer/parallel port is a standard 25-pin DB-25 female port.Monitor PortThe monitor port is a

Identifying Components13Mic, Line In, and Headphones JacksThe mic, line in, and headphones jacks are physically identical, but havedifferent connectio

VAIO® System Reference Manual14i.LINK® (IEEE1394) PortThe 6-pin i.LINK port on the back of the system can supply power fromthe computer to a device if

Identifying Components15Expansion SlotsTherearethreePCIslots,twoofwhichareavailableforexpansion(PCINo. 2 and No. 3). The other PCI slot is occupied by

iiiSafety Information and Caution ❑ To prevent fire or shock hazard, donot expose your desktop to rain ormoisture.To avoid electrical shock,do not ope

VAIO® System Reference Manual16

17Chapter 2Configuring Your SystemThis chapter contains information on configuring your system.Configuring your system can consist of the following:❑

VAIO® System Reference Manual18Accessing the BIOS Setup UtilityYou must access the BIOS Setup Utility to make changes to the BIOSsettings (see “CMOS S

Configuring Your System19Changing the Display's Power Management SettingsA display that has power management capability is designed to operateon

VAIO® System Reference Manual20The Turn off monitor option allows you to specify the period ofinactivity (in minutes) that you want to elapse before y

Configuring Your System214 Click the Advanced tab.5 Select the desired settings.

VAIO® System Reference Manual226 Click the Hibernate tab.7 Select the desired settings, and then click OK.

23Chapter 3Removing, Installing, and Replacing ComponentsThis chapter describes removing, installing, and replacing majorcomponents for upgrading, rec

VAIO® System Reference Manual24Removing the Side Cover You must remove the side cover to access the system board, add-in cards,power supply, battery,

Removing, Installing, and Replacing Components25Replacing the Side Cover 1 From the rear of the unit, align the bottom of the side cover so that itsli

iv❑ Pour prévenir tout risque d’incendieou d’électrocution, garder cet appareilà l’abri de la pluie et de l’humidité.❑ Pour prévenir tout risqued’élec

VAIO® System Reference Manual26Installing a PCI Add-In Card 1 Remove the side cover (see “Removing the Side Cover” on page 24).2 Locate an available

Removing, Installing, and Replacing Components278 Turn on the computer and follow any instructions that came with theadd-in card.Removing a PCI Add-in

VAIO® System Reference Manual284 Removetheadd-incardfromthePCIslotandstorethecardinananti-static wrapper for future use.5 If you do not replace the ca

Removing, Installing, and Replacing Components29Installing an Add-On AGP CardYour computer has one open AGP expansion slot. This slot enables you toin

VAIO® System Reference Manual306 Secure the AGP card with the screw removed in step 2.7 Replace the side cover (see “ReplacingtheSideCover”on page 25)

Removing, Installing, and Replacing Components31Replacing the Lithium Battery You may need to replace the lithium battery if your computer consistentl

VAIO® System Reference Manual328 If necessary, remove any add-in cards (see “Removing a PCI Add-inCard” on page 27) to gain access to the battery. You

Removing, Installing, and Replacing Components3316 If the error message “Error: Check date and time settings.” appearsduring the reboot sequence, pres

VAIO® System Reference Manual34Installing System Memory 1 Choose the size of the memory module and configuration as shownin the following table. Memor

Removing, Installing, and Replacing Components357 Align the module over the appropriate slot, noting the location of pin1 on the module and pin 1 on t

vRegulatory InformationThis equipment has been tested and foundto comply with the limits for a Class Bdigital device, pursuant to Part 15 of theRules.

VAIO® System Reference Manual3610 Replace the power supply (see “Replacing the Power Supply” onpage 46).11 Replace the side cover (see “ReplacingtheSi

Removing, Installing, and Replacing Components37Removing a Memory Module You may need to remove a memory module if you change the memoryconfiguration

VAIO® System Reference Manual384 Reach around each side of the power supply and push down thehandleoneachsideofthememorymoduletoejectthemodulefromits

Removing, Installing, and Replacing Components39Removing a Slot CoverYouremoveaslotcoverwhenyouinstallanadd-incardthatoccupiesapreviously-empty slot.1

VAIO® System Reference Manual40Covering an Open I/O Slot Slot covers prevent air from escaping through the empty hole. If airescapes, the components i

Removing, Installing, and Replacing Components41Installing a 3.5-inch Internal Hard Disk DriveYour system comes with an available bay to hold an addit

VAIO® System Reference Manual423 Disconnect the drive connector (A in diagram).4 Disconnect the power connector (B in diagram).5 Pull out on the tab (

Removing, Installing, and Replacing Components436 Slidethedriveholderupandout.7 Slide the new drive into the bottom part of the drive holder and align

VAIO® System Reference Manual4410 Push in on the tab (A) to securely latch the holder to the chassis.11 Connect the inner drive cable connector (B) to

Removing, Installing, and Replacing Components45Removing the Power SupplyYou remove the power supply when you insert a memory module (see“Installing S

viFCC Part 68This equipment complies with Part 68 of theFCC rules. The FCC Ringer EquivalenceNumber (REN) for this equipment is 0.79B. Ifrequested, th

VAIO® System Reference Manual46Replacing the Power Supply1 Rotate the power supply down and slide it into the chassis along therails to each side of t

47Chapter 4System BoardThis chapter identifies each component on the system board and providesa detailed description of each header, connector, and ju

VAIO® System Reference Manual48Connectors and HeadersFront Panel HeaderThefrontpanelheaderisa20-pinheader(onepinisremovedforthekey)that provides conne

System Board49Floppy Disk Drive Header33 3421Key (pin 5)

VAIO® System Reference Manual50Memory Module (DIMM) SlotsBoth sides of each Dual Inline Memory Module (DIMM) look verysimilar. The side with pin 1 has

System Board51PCI Slots There are a total of three PCI slots (slots No. 1 to No. 3). Two PCI slots(No. 2 and No. 3) are available. The other PCI slot

VAIO® System Reference Manual52AGP SlotThere is one AGP slot (slot No. 4). This slot enables you to install an AGPcard to enhance your system’s graphi

System Board53IDE HeadersThere are two IDE (Integrated Drive Electronics) headers on the systemboard: a Primary IDE and a Secondary IDE header.Each 40

VAIO® System Reference Manual54Keyboard and Mouse PortsThekeyboardportandthemouseportare6-pinfemalePS/2-type(mini-DIN) ports. They have identical pino

System Board55USB Ports, USB Header, and Ethernet PortThere are three USB ports that permit connection of three USB peripheraldevices directly to the

viiTelephone Consumer Guidelines (Canada)Please refer to your telephone directoryunder‘PrivacyIssues’and/or‘TermsofService.’ For more detailed informa

VAIO® System Reference Manual5611 Ground12 Ground* Uses over-current protector.USB1 and Ethernet portPin Signal Name1 ACTLEDP2 ACTLEDN3 LILEDP4 LILEDN

System Board57Printer, Monitor, and i.LINK ConnectorsThe printer, monitor, and i.LINK (IEEE1394) connectors are mounted in asingle bracket on the syst

VAIO® System Reference Manual5813 SELECT14 AUTO-FEED -15 ERROR -16 INIT -17 SELECT-IN -18 LOGIC GND19 LOGIC GND20 LOGIC GND21 LOGIC GND22 LOGIC GND23

System Board59i.LINK connectorPin Signal Name1VP(Power)*2Ground3TPB4TPB5TPA6TPA* Uses over-current protector.

VAIO® System Reference Manual60i.LINK Headeri.LINK header is an 8-pin header that connects to a 4-pin i.LINKconnector that is accessible at the bottom

System Board61Serial Port, Headphones, Line In, and Mic ConnectorsThe serial connector is a DB-9 male connector. The headphones, line in,and mic jacks

VAIO® System Reference Manual62Headphones Line In Mic Audio Right OutAudio Left OutAudio Right InL ImbalanceAudio Left InElectret bias voltageMIC im

System Board63Power Supply HeaderThe power supply header on the system board connects to the powersupply connector labelled P1.2011110

VAIO® System Reference Manual64Fan HeadersThe CPU-FAN and PWR-FAN headers are 1 x 3-pin straight headers. TheCPU_FAN header connects to the CPU fan an

System Board65CD-In HeaderThe CD-In header on the system board is a 1 x 4-pin header that connectsto the DVD-ROM drive.CD-In headerPin Signal Name1Lef

viiiIndustry Canada NoticeNOTICE: The Industry Canada labelidentifies certified equipment. Thiscertification means that the equipment meetscertain tel

VAIO® System Reference Manual66Wake On LAN (WOL-CON) HeaderThe Wake On LAN header (WOL-CON) on the system board is a 3-pinheader. It is not used.Wake

System Board67AUX Audio HeaderTheAUXAudioheaderisa4pinstandard2mmsinglelineheaderthatconnects to the AUX Audio signal input (not used).AUX Audio heade

VAIO® System Reference Manual68Configuration Jumper (CMOS CLR)There is one user-configurable jumper for CMOS Clear.The computer ships with CMOS Clear

69Chapter 5Fax/Modem CardThe fax/modem card occupies PCI slot No. 1. Your computer is eitherinstalled with a HomePNA modem or Lucent 1648 modem depend

VAIO® System Reference Manual70HomePNA ModemThe HomePNA standard uses frequency division multiplexing (FDM) tousethesamephonelineforvoiceanddatatransm

Fax/Modem Card71Lucent 1648 ModemThere are two RJ-11 jacks: one to connect a telephone line, and one toconnect a phone.Connectors Name Connector Type

VAIO® System Reference Manual72

73Chapter 6CMOS Setup OptionsThis chapter describes each screen in the Award BIOS Setup Utility (see“Accessing the BIOS Setup Utility” on page 18).The

VAIO® System Reference Manual74Press F10 to save the changes and exit, or press Esc to discard thechanges.Follow the on-screen prompts for other choic

CMOS Setup Options75Main Screen System Time [00:00:00]System Date [01/01/2001]Primary Master (see“IDE Sub-Menus”on page 76)Primary Slave (see“IDE Sub-

ixensemble. Cette précaution estparticulièrement importante dans lesrégions rurales.Avertissement: L’utilisateur ne doit pastenter de faire ces raccor

VAIO® System Reference Manual76IDE Sub-MenusType [Auto]User Type HDDCD-ROMLS-120ZIP-100MOOther ATAPI DeviceNoneTranslation Method*[LBA]LargeNormalMatc

CMOS Setup Options77Advanced Screen CPU Speed 1000 MHz (PCV-RX450)1200 MHz (PCV-RX460)I/O Device ConfigurationOnboard AC97 Audio Controller [Enabled]D

VAIO® System Reference Manual78Power ScreenPower Up ControlAC Power Loss Restart [Disabled]EnabledPower Up On Modem Act [Disabled]EnabledWake On LAN [

CMOS Setup Options79Boot Screen 1. ATAPI CD-ROM [(displays installed drive)]Disabled2. Removable Device [Legacy Floppy]LS120ZIP-100ATAPI MODisabled3.

VAIO® System Reference Manual80Exit ScreenExit Saving ChangesExit Discarding ChangesLoad Setup DefaultsDiscard ChangesSave Changes

81Chapter 7Miscellaneous Technical InformationThis chapter contains information on the following subjects:❑ User and Supervisor password❑ Beep code er

VAIO® System Reference Manual82About User and Supervisor Passwords The system allows you to specify up to two passwords (a User passwordand a Supervis

Miscellaneous Technical Information83Beep Code Error Messages During a normal bootup, a single short beep signifies that the system isOK. Other beep p

VAIO® System Reference Manual84PCI Configuration Status and Error Messages The following is a list of status and error messages that may appear onyour

Miscellaneous Technical Information85DMA Channel Assignments This shows the factory default values. The Microsoft® Windows® Meoperating system reassig